• Subscribe
gaomiwood@timberpart.com

Drawers Specifications Example

Drawers Specifications Example of bulk order

This is just for reference and shows how it works with us.

 

Specifications                
Thickness: Even Thickness should be maintained throughout          
Tolerance: +0.5/-0.25mm              
Width: According to sizes on parts list            
Tolerance: +/-0.75mm              
Length: According to sizes on parts list            
Tolerance: +/-0.75mm              
Square: All dimesnional cuts are to be square throughout the part.        
  End cuts are to be square from the bottom face.          
Tolerance: 49 – 102mm Width   Less than or equal to 0.5mm tolerance      
  141 – 302mm Width Less than or equal to 0.75mm tolerance      
  252 – 254mm Width Less than or equal to 0.9mm tolerance      
Finish: Two Faces and Top and Bottom Edge          
  End Grain of Fronts/Backs MUST be finished and Must reach the level as per standard      
  End Grain of Sides also needs to finish as seal / sand / seal        
  Bottom Edge must be finished on all parts.          
  1219mm length parts are also required end finish as seal / sand / seal        
Wood strip glue up 25mm minimum stave width. Staves on top and bottom edge do not have a minimum width.    
  Only 15% of interior staves may be 25mm. 85% will range between 35 and 50mm      
  Parts must be well color matched.            
Moisture Content: 90% of production reach 8% to 12% and maximum 10% of production allowed 6% to 7.9%.    



  Character/Defect:                
  Sides:                
  Groove Face: Well color matched and allow up to two of max 3mm(.118″) diamter pin knots per every 500mm of length on face.  
    Up to 15% of parts may have one 25mm(1″) light-medium brown live sound knot.      
    Mineral/Fleck:Per every 500mm of length on face can accept up to four per face within 1mm×25mm(.04″ x 1″).  
  Non Groove Face: Mostly well color matched and allow up to three of max 6mm(.24″) diameter pin knots per every 500mm of length on face.  
    Up to 15% of parts may have one 25mm(1″) light-medium brown live sound knot.      
    Mineral/Fleck:Per every 500mm of length on face can accept combined up to 2mm×50mm(.08″ x 2″).    
  Front/Backs:                
  Groove Face: Mostly well color matched and allow up to three of max 6mm(.24″) diameter pin knots per every 500mm of length on face.  
    Up to 15% of parts may have one 25mm(1″) light-medium brown live sound knot.      
    Mineral/Fleck:Per every 500mm of length on face can accept combined up to 2mm×50mm(.08″ x 2″).    
  Non Groove Face: Allows large dark knots, grain or color variations and other defects that have been repaired    
    with similar color putty as the surrounding area. Repairs must maintain consistent dimensional characteristic as outlined above.
    Dark putty allowed to repair knots to look natural.          
  SPECIAL NOTE: Any color allowed below the groove for both sides and fronts/backs on the groove face only.    
    No knots allowed on ends of parts.          
  Radius: 1.91mm chamfer on all four corners          

 

 

  Packaging:              
    Only one part number per pallet allowed        
    Pallet size must be 42″ Deep x 36″ Width. (42″ deep is where the fork openings go)    
    One pallet tag per pallet. Pallet tag located on 42″ side with fork openings and facing the opening of the container when loading.
    Double Band Pallet in both directions        
    On the pallet leg, fresh color print is required on both forklift open side      
    Max allowed 3 different parts No# load into the same pallet if the order quantity very small.  
    But must has cardboards put between the different part No#s and must have shrink wrap based on required pallet quantity.
    On the pallet tag must contains all the different part numbers on the pallet    
    Pallets must has 4 opening to ensure the lift fork can goes in from all 4 ways.    
    The total pallet heights(After load drawer parts) must not over 44” (Included pallet height)  
Maximum Pallet Quantities and Estimated Usage
                 
    Thick Height Length SQFT Qty/Pallet Usage  
                 
    15.875 102 218.6 0.240 1200 6392  
    15.875 102 294.8 0.324 1800 12748  
    15.875 102 371 0.407 1320 26774  
    15.875 102 447.2 0.491 1200 20999  
    15.875 102 495.3 0.544 1080 8298  
    15.875 102 523.4 0.575 960 12571  
    15.875 102 599.6 0.658 780 12053  
    15.875 102 647.7 0.711 720 5236  
    15.875 102 675.8 0.742 720 6615  
    15.875 102 800.1 0.878 660 10396  
    15.875 102 828.2 0.909 600 3997  
    15.875 153 294.8 0.485 660 4669  
    15.875 153 371 0.611 960 6155  
    15.875 153 447.2 0.736 300 2875  
    15.875 203 294.8 0.644 900 7747  
    15.875 203 371 0.811 600 7673  
    15.875 203 447.2 0.977 600 1663  
    15.875 203 599.6 1.310 360 1232  
    15.875 203 675.8 1.477 360 1717  

SEND YOUR REQUEST NOW FOR CUSTOM-MADE DRAWERS:

Name

Email

Message